- #Mweb adsl router settings code#
- #Mweb adsl router settings password#
- #Mweb adsl router settings Pc#
Method 4: Use the WPS button (for WPS-supported device only) Note: If you want to connect to a 5 GHz Wi-Fi, try Method 2. Scan it with your phone or tablet to join the preset 2.4 GHz Wi-Fi d irectly.
#Mweb adsl router settings code#
Method 3: Connect via QR code (for smart device only)įind the QR code printed on the label of the router.
#Mweb adsl router settings password#
Select the SSID and then enter the corresponding password to join the network.
#Mweb adsl router settings Pc#
Go to the Wi-Fi settings of your PC or smart device. Locate the SSID (Network Name) and Wireless Password printed on the label of the router.Ģ. Method 2: Connect via Wi-Fi settings (for PC or smart device)ġ. Method 1: Connect via an ethernet cable (for PC only)ĭirectly connect the computer to the router’s LAN or Ethernet port via a network cable. Step 1 Connect your device to a Wi-Fi router Once you‘ve accessed your router, you can change wireless network name and password, configure advanced features like Parental Controls and Guest Network, set LED Schedule of your router and so on. The DNS servers can be obtained by your router using DHCPv6 over PPP.How to Access Your Wi-Fi Router’s Settings These are our customer facing DNS resolvers for IPv6 use. If configuring manually please use these two addresses as our main customer facing DNS resolvers. These are provided to your router via PPP, and some routers will provide a DNS relay feature allowing you to use your local router LAN IP address as a DNS service. This will depend on how you set up your network and your DSL router. Your PC/router will normally be configured to obtain an IP address and DNS servers automatically, and so not need any special set up. Typically you'll have a PPPoE capable router and will connect the WAN port to the CityFibre ONT that was installed by CityFibre. If your router cannot handle the length of password we provide, please contact support who will be happy to set a shorter password. If you change the password on our system your lines will go off line until you change the password on the router as well. We allocate a password, but you can change this on the Broadband Control Pages. Leave untagged, no VLAN, and connect your router to the Openreach ONT
Typically you'll have a PPPoE capable router and will connect the WAN port to the Openreach ONT that was installed by Openreach. Use this if your router has a built in VDSL modem. (Not applicable if you are using the Openreach modem). Some customers may have a separate Openreach modem, and will then use a PPPoE router. Typically you'll have a FTTC capable router (ie a router with a built in FTTC/VDSL modem) and will use PPPoE, and you'll need to set a VLAN in the PPPoE settings. For FTTC and FTTP the only operational mode is PPPoE directly with RFC4638 support allowing 1500 byte MTU. In such cases you need the LLC-Mux normally. This can be useful when using a bridging modem. Please note that most DSL lines (BT and TT) do allow PPPoE mode. You may want your DSL router to act as a DHCP server for your LAN.
If you have a separate router/firewall link block, you will need to configure a static route for your main IP block via your router/firewall. DO NOT make up a netmask for use with a real IP address that we have allocated - always use the one we have advised. If you have a block of IPs from us, use the IP and netmask as advised. If using NAT then this will be some default such as 192.168.1.254. This will change depending on equipment at our end and may even change on every connection in the future. The IP address for our end of the PPP link should not be configured. If you configure this incorrectly you will normally find you cannot log in at all. Whilst we allocate a fixed IP address for your service, including the WAN address, it is best not to set this as it is allocated automatically using PPP. We allocate a password, but you can change this on the Broadband Control Pages. 1, 2, etc.) for where customers have multiple lines sharing IP addresses. The final number is the line number (e.g. This is of the form of a name followed by a realm, a dot then a single digit number. We allocate a login for one or more lines. This is often the default on most broadband routers PPPoE (see below) is more commonly used when bridging to a separate PPPoE device such as a FireBrick When routing IP you want your router to connect using PPPoA mode. This means that IP traffic is routed, and is the normal mode unless setting up a PPPoE bridge to another device. Usually set this to automatic as it allows ADSL or ADSL2+ (depending on modem and line type). ADSL: Basic BT and TT PPPoA Settings Setting
0 kommentar(er)
